forked from Misaka-blog/3x-ui
-
Notifications
You must be signed in to change notification settings - Fork 0
/
x-ui.sh
1399 lines (1274 loc) · 39.2 KB
/
x-ui.sh
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
#!/bin/bash
red='\033[0;31m'
green='\033[0;32m'
yellow='\033[0;33m'
plain='\033[0m'
#Add some basic function here
function LOGD() {
echo -e "${yellow}[DEG] $* ${plain}"
}
function LOGE() {
echo -e "${red}[ERR] $* ${plain}"
}
function LOGI() {
echo -e "${green}[INF] $* ${plain}"
}
# check root
[[ $EUID -ne 0 ]] && echo -e "${red}致命错误: ${plain} 请使用 root 权限运行此脚本\n" && exit 1
# Check OS and set release variable
if [[ -f /etc/os-release ]]; then
source /etc/os-release
release=$ID
elif [[ -f /usr/lib/os-release ]]; then
source /usr/lib/os-release
release=$ID
else
echo "检查服务器操作系统失败，请联系作者!" >&2
exit 1
fi
echo "目前服务器的操作系统为: $release"
os_version=$(grep -i version_id /etc/os-release | cut -d \" -f2 | cut -d . -f1)
if [[ "${release}" == "centos" ]]; then
if [[ ${os_version} -lt 8 ]]; then
echo -e "${red} 请使用 CentOS 8 或更高版本 ${plain}\n" && exit 1
fi
elif [[ "${release}" == "ubuntu" ]]; then
if [[ ${os_version} -lt 20 ]]; then
echo -e "${red} 请使用 Ubuntu 20 或更高版本!${plain}\n" && exit 1
fi
elif [[ "${release}" == "fedora" ]]; then
if [[ ${os_version} -lt 36 ]]; then
echo -e "${red} 请使用 Fedora 36 或更高版本!${plain}\n" && exit 1
fi
elif [[ "${release}" == "debian" ]]; then
if [[ ${os_version} -lt 11 ]]; then
echo -e "${red} 请使用 Debian 11 或更高版本 ${plain}\n" && exit 1
fi
elif [[ "${release}" == "almalinux" ]]; then
if [[ ${os_version} -lt 9 ]]; then
echo -e "${red} 请使用 AlmaLinux 9 或更高版本 ${plain}\n" && exit 1
fi
elif [[ "${release}" == "rocky" ]]; then
if [[ ${os_version} -lt 9 ]]; then
echo -e "${red} 请使用 RockyLinux 9 或更高版本 ${plain}\n" && exit 1
fi
elif [[ "${release}" == "arch" ]]; then
echo "您的操作系统是 ArchLinux"
elif [[ "${release}" == "manjaro" ]]; then
echo "您的操作系统是 Manjaro"
elif [[ "${release}" == "armbian" ]]; then
echo "您的操作系统是 Armbian"
elif [[ "${release}" == "oracle" ]]; then
if [[ ${os_version} -lt 8 ]]; then
echo -e "${red} 请使用 Oracle Linux 8 或更高版本 ${plain}\n" && exit 1
fi
else
echo -e "${red}此脚本不支持您的操作系统。${plain}\n"
echo "请确保您使用的是以下受支持的操作系统之一："
echo "- Ubuntu 20.04+"
echo "- Debian 11+"
echo "- CentOS 8+"
echo "- Fedora 36+"
echo "- Arch Linux"
echo "- Manjaro"
echo "- Armbian"
echo "- AlmaLinux 9+"
echo "- Rocky Linux 9+"
echo "- Oracle Linux 8+"
exit 1
fi
# Declare Variables
log_folder="${XUI_LOG_FOLDER:=/var/log}"
iplimit_log_path="${log_folder}/3xipl.log"
iplimit_banned_log_path="${log_folder}/3xipl-banned.log"
confirm() {
if [[ $# > 1 ]]; then
echo && read -p "$1 [Default $2]: " temp
if [[ "${temp}" == "" ]]; then
temp=$2
fi
else
read -p "$1 [y/n]: " temp
fi
if [[ "${temp}" == "y" || "${temp}" == "Y" ]]; then
return 0
else
return 1
fi
}
confirm_restart() {
confirm "重启面板，注意：重启面板也会重启 xray" "y"
if [[ $? == 0 ]]; then
restart
else
show_menu
fi
}
before_show_menu() {
echo && echo -n -e "${yellow}按 Enter 键返回主菜单：${plain}" && read temp
show_menu
}
install() {
bash <(curl -Ls https://raw.githubusercontent.com/Misaka-blog/3x-ui/main/install.sh)
if [[ $? == 0 ]]; then
if [[ $# == 0 ]]; then
start
else
start 0
fi
fi
}
update() {
confirm "该功能将强制安装最新版本，并且数据不会丢失。你想继续吗?" "y"
if [[ $? != 0 ]]; then
LOGE "已取消"
if [[ $# == 0 ]]; then
before_show_menu
fi
return 0
fi
bash <(curl -Ls https://raw.githubusercontent.com/Misaka-blog/3x-ui/main/install.sh)
if [[ $? == 0 ]]; then
LOGI "更新完成，面板已自动重启"
exit 0
fi
}
custom_version() {
echo "输入面板版本 (例: 2.0.0):"
read panel_version
if [ -z "$panel_version" ]; then
echo "面板版本不能为空。"
exit 1
fi
download_link="https://raw.githubusercontent.com/Misaka-blog/3x-ui/master/install.sh"
# Use the entered panel version in the download link
install_command="bash <(curl -Ls $download_link) v$panel_version"
echo "下载并安装面板版本 $panel_version..."
eval $install_command
}
# Function to handle the deletion of the script file
delete_script() {
rm "$0" # Remove the script file itself
exit 1
}
uninstall() {
confirm "您确定要卸载面板吗? xray 也将被卸载!" "n"
if [[ $? != 0 ]]; then
if [[ $# == 0 ]]; then
show_menu
fi
return 0
fi
systemctl stop x-ui
systemctl disable x-ui
rm /etc/systemd/system/x-ui.service -f
systemctl daemon-reload
systemctl reset-failed
rm /etc/x-ui/ -rf
rm /usr/local/x-ui/ -rf
echo ""
echo -e "卸载成功\n"
echo "如果您需要再次安装此面板，可以使用以下命令:"
echo -e "${green}bash <(curl -Ls https://raw.githubusercontent.com/Misaka-blog/3x-ui/master/install.sh)${plain}"
echo ""
# Trap the SIGTERM signal
trap delete_script SIGTERM
delete_script
}
reset_user() {
confirm "您确定重置面板的用户名和密码吗?" "n"
if [[ $? != 0 ]]; then
if [[ $# == 0 ]]; then
show_menu
fi
return 0
fi
read -rp "请设置用户名 [默认为随机用户名]: " config_account
[[ -z $config_account ]] && config_account=$(date +%s%N | md5sum | cut -c 1-8)
read -rp "请设置密码 [默认为随机密码]: " config_password
[[ -z $config_password ]] && config_password=$(date +%s%N | md5sum | cut -c 1-8)
/usr/local/x-ui/x-ui setting -username ${config_account} -password ${config_password} >/dev/null 2>&1
/usr/local/x-ui/x-ui setting -remove_secret >/dev/null 2>&1
echo -e "面板登录用户名已重置为：${green} ${config_account} ${plain}"
echo -e "面板登录密码已重置为：${green} ${config_password} ${plain}"
echo -e "${yellow} 面板 Secret Token 已禁用 ${plain}"
echo -e "${green} 请使用新的登录用户名和密码访问 X-UI 面板。也请记住它们！${plain}"
confirm_restart
}
reset_config() {
confirm "您确定要重置所有面板设置，帐户数据不会丢失，用户名和密码不会更改" "n"
if [[ $? != 0 ]]; then
if [[ $# == 0 ]]; then
show_menu
fi
return 0
fi
/usr/local/x-ui/x-ui setting -reset
echo -e "所有面板设置已重置为默认，请立即重新启动面板，并使用默认的${green}2053${plain}端口访问网页面板"
confirm_restart
}
check_config() {
info=$(/usr/local/x-ui/x-ui setting -show true)
if [[ $? != 0 ]]; then
LOGE "获取当前设置错误，请检查日志"
show_menu
fi
LOGI "${info}"
}
set_port() {
echo && echo -n -e "输入端口号 [1-65535]: " && read port
if [[ -z "${port}" ]]; then
LOGD "Cancelled"
before_show_menu
else
/usr/local/x-ui/x-ui setting -port ${port}
echo -e "端口已设置，请立即重启面板，并使用新端口 ${green}${port}${plain} 以访问面板"
confirm_restart
fi
}
start() {
check_status
if [[ $? == 0 ]]; then
echo ""
LOGI "面板正在运行，无需再次启动，如需重新启动，请选择重新启动"
else
systemctl start x-ui
sleep 2
check_status
if [[ $? == 0 ]]; then
LOGI "x-ui 已成功启动"
else
LOGE "面板启动失败，可能是启动时间超过两秒，请稍后查看日志信息"
fi
fi
if [[ $# == 0 ]]; then
before_show_menu
fi
}
stop() {
check_status
if [[ $? == 1 ]]; then
echo ""
LOGI "面板已关闭，无需再次关闭！"
else
systemctl stop x-ui
sleep 2
check_status
if [[ $? == 1 ]]; then
LOGI "x-ui 和 xray 已成功关闭"
else
LOGE "面板关闭失败，可能是停止时间超过两秒，请稍后查看日志信息"
fi
fi
if [[ $# == 0 ]]; then
before_show_menu
fi
}
restart() {
systemctl restart x-ui
sleep 2
check_status
if [[ $? == 0 ]]; then
LOGI "x-ui and xray 已成功重启"
else
LOGE "面板重启失败，可能是启动时间超过两秒，请稍后查看日志信息"
fi
if [[ $# == 0 ]]; then
before_show_menu
fi
}
status() {
systemctl status x-ui -l
if [[ $# == 0 ]]; then
before_show_menu
fi
}
enable() {
systemctl enable x-ui
if [[ $? == 0 ]]; then
LOGI "x-ui 已成功设置开机启动"
else
LOGE "x-ui 设置开机启动失败"
fi
if [[ $# == 0 ]]; then
before_show_menu
fi
}
disable() {
systemctl disable x-ui
if [[ $? == 0 ]]; then
LOGI "x-ui 已成功取消开机启动"
else
LOGE "x-ui 取消开机启动失败"
fi
if [[ $# == 0 ]]; then
before_show_menu
fi
}
show_log() {
journalctl -u x-ui.service -e --no-pager -f
if [[ $# == 0 ]]; then
before_show_menu
fi
}
show_banlog() {
if test -f "${iplimit_banned_log_path}"; then
if [[ -s "${iplimit_banned_log_path}" ]]; then
cat ${iplimit_banned_log_path}
else
echo -e "${red}日志文件为空${plain}\n"
fi
else
echo -e "${red}未找到日志文件。 请先安装 Fail2ban 和 IP Limit${plain}\n"
fi
}
bbr_menu() {
echo -e "${green}\t1.${plain} 启用 BBR"
echo -e "${green}\t2.${plain} 禁用 BBR"
echo -e "${green}\t0.${plain} 返回主菜单"
read -p "请输入选项: " choice
case "$choice" in
0)
show_menu
;;
1)
enable_bbr
;;
2)
disable_bbr
;;
*) echo "无效选项" ;;
esac
}
disable_bbr() {
if ! grep -q "net.core.default_qdisc=fq" /etc/sysctl.conf || ! grep -q "net.ipv4.tcp_congestion_control=bbr" /etc/sysctl.conf; then
echo -e "${yellow}BBR 当前未启用${plain}"
exit 0
fi
# Replace BBR with CUBIC configurations
sed -i 's/net.core.default_qdisc=fq/net.core.default_qdisc=pfifo_fast/' /etc/sysctl.conf
sed -i 's/net.ipv4.tcp_congestion_control=bbr/net.ipv4.tcp_congestion_control=cubic/' /etc/sysctl.conf
# Apply changes
sysctl -p
# Verify that BBR is replaced with CUBIC
if [[ $(sysctl net.ipv4.tcp_congestion_control | awk '{print $3}') == "cubic" ]]; then
echo -e "${green}BBR 已成功替换为 CUBIC${plain}"
else
echo -e "${red}用 CUBIC 替换 BBR 失败，请检查您的系统配置。${plain}"
fi
}
enable_bbr() {
if grep -q "net.core.default_qdisc=fq" /etc/sysctl.conf && grep -q "net.ipv4.tcp_congestion_control=bbr" /etc/sysctl.conf; then
echo -e "${green}BBR 已经启用!${plain}"
exit 0
fi
# Check the OS and install necessary packages
case "${release}" in
ubuntu | debian | armbian)
apt-get update && apt-get install -yqq --no-install-recommends ca-certificates
;;
centos | almalinux | rocky | oracle)
yum -y update && yum -y install ca-certificates
;;
fedora)
dnf -y update && dnf -y install ca-certificates
;;
arch | manjaro)
pacman -Sy --noconfirm ca-certificates
;;
*)
echo -e "${red}不支持的操作系统。请检查脚本并手动安装必要的软件包${plain}\n"
exit 1
;;
esac
# Enable BBR
echo "net.core.default_qdisc=fq" | tee -a /etc/sysctl.conf
echo "net.ipv4.tcp_congestion_control=bbr" | tee -a /etc/sysctl.conf
# Apply changes
sysctl -p
# Verify that BBR is enabled
if [[ $(sysctl net.ipv4.tcp_congestion_control | awk '{print $3}') == "bbr" ]]; then
echo -e "${green}BBR 已成功启用${plain}"
else
echo -e "${red}启用 BBR 失败，请检查您的系统配置${plain}"
fi
}
update_shell() {
wget -O /usr/bin/x-ui -N --no-check-certificate https://github.com/Misaka-blog/3x-ui/raw/main/x-ui.sh
if [[ $? != 0 ]]; then
echo ""
LOGE "下载脚本失败，请检查机器是否可以连接至 GitHub"
before_show_menu
else
chmod +x /usr/bin/x-ui
LOGI "升级脚本成功，请重新运行脚本" && exit 0
fi
}
# 0: running, 1: not running, 2: not installed
check_status() {
if [[ ! -f /etc/systemd/system/x-ui.service ]]; then
return 2
fi
temp=$(systemctl status x-ui | grep Active | awk '{print $3}' | cut -d "(" -f2 | cut -d ")" -f1)
if [[ "${temp}" == "running" ]]; then
return 0
else
return 1
fi
}
check_enabled() {
temp=$(systemctl is-enabled x-ui)
if [[ "${temp}" == "enabled" ]]; then
return 0
else
return 1
fi
}
check_uninstall() {
check_status
if [[ $? != 2 ]]; then
echo ""
LOGE "面板已安装，请勿重新安装"
if [[ $# == 0 ]]; then
before_show_menu
fi
return 1
else
return 0
fi
}
check_install() {
check_status
if [[ $? == 2 ]]; then
echo ""
LOGE "请先安装面板"
if [[ $# == 0 ]]; then
before_show_menu
fi
return 1
else
return 0
fi
}
show_status() {
check_status
case $? in
0)
echo -e "面板状态: ${green}运行中${plain}"
show_enable_status
;;
1)
echo -e "面板状态: ${yellow}未运行${plain}"
show_enable_status
;;
2)
echo -e "面板状态: ${red}未安装${plain}"
;;
esac
show_xray_status
}
show_enable_status() {
check_enabled
if [[ $? == 0 ]]; then
echo -e "开机启动: ${green}是${plain}"
else
echo -e "开机启动: ${red}否${plain}"
fi
}
check_xray_status() {
count=$(ps -ef | grep "xray-linux" | grep -v "grep" | wc -l)
if [[ count -ne 0 ]]; then
return 0
else
return 1
fi
}
show_xray_status() {
check_xray_status
if [[ $? == 0 ]]; then
echo -e "xray 状态: ${green}运行中${plain}"
else
echo -e "xray 状态: ${red}未运行${plain}"
fi
}
firewall_menu() {
echo -e "${green}\t1.${plain} 安装防火墙并开放端口"
echo -e "${green}\t2.${plain} 允许列表"
echo -e "${green}\t3.${plain} 从列表中删除端口"
echo -e "${green}\t4.${plain} 禁用防火墙"
echo -e "${green}\t0.${plain} 返回主菜单"
read -p "请输入选项: " choice
case "$choice" in
0)
show_menu
;;
1)
open_ports
;;
2)
sudo ufw status
;;
3)
delete_ports
;;
4)
sudo ufw disable
;;
*) echo "无效选项" ;;
esac
}
open_ports() {
if ! command -v ufw &>/dev/null; then
echo "ufw 防火墙未安装，正在安装..."
apt-get update
apt-get install -y ufw
else
echo "ufw 防火墙已安装"
fi
# Check if the firewall is inactive
if ufw status | grep -q "Status: active"; then
echo "防火墙已经激活"
else
# Open the necessary ports
ufw allow ssh
ufw allow http
ufw allow https
ufw allow 2053/tcp
# Enable the firewall
ufw --force enable
fi
# Prompt the user to enter a list of ports
read -p "输入您要打开的端口（例如 80,443,2053 或端口范围 400-500): " ports
# Check if the input is valid
if ! [[ $ports =~ ^([0-9]+|[0-9]+-[0-9]+)(,([0-9]+|[0-9]+-[0-9]+))*$ ]]; then
echo "错误：输入无效。请输入以逗号分隔的端口列表或端口范围（例如 80,443,2053 或 400-500)" >&2
exit 1
fi
# Open the specified ports using ufw
IFS=',' read -ra PORT_LIST <<<"$ports"
for port in "${PORT_LIST[@]}"; do
if [[ $port == *-* ]]; then
# Split the range into start and end ports
start_port=$(echo $port | cut -d'-' -f1)
end_port=$(echo $port | cut -d'-' -f2)
# Loop through the range and open each port
for ((i = start_port; i <= end_port; i++)); do
ufw allow $i
done
else
ufw allow "$port"
fi
done
# Confirm that the ports are open
ufw status | grep $ports
}
delete_ports() {
# Prompt the user to enter the ports they want to delete
read -p "输入要删除的端口（例如 80,443,2053 或范围 400-500): " ports
# Check if the input is valid
if ! [[ $ports =~ ^([0-9]+|[0-9]+-[0-9]+)(,([0-9]+|[0-9]+-[0-9]+))*$ ]]; then
echo "错误：输入无效。请输入以逗号分隔的端口列表或端口范围（例如 80,443,2053 或 400-500)" >&2
exit 1
fi
# Delete the specified ports using ufw
IFS=',' read -ra PORT_LIST <<<"$ports"
for port in "${PORT_LIST[@]}"; do
if [[ $port == *-* ]]; then
# Split the range into start and end ports
start_port=$(echo $port | cut -d'-' -f1)
end_port=$(echo $port | cut -d'-' -f2)
# Loop through the range and delete each port
for ((i = start_port; i <= end_port; i++)); do
ufw delete allow $i
done
else
ufw delete allow "$port"
fi
done
# Confirm that the ports are deleted
echo "删除指定端口:"
ufw status | grep $ports
}
update_geo() {
local defaultBinFolder="/usr/local/x-ui/bin"
read -p "请输入 x-ui bin 文件夹路径，默认留空。（默认值：'${defaultBinFolder}')" binFolder
binFolder=${binFolder:-${defaultBinFolder}}
if [[ ! -d ${binFolder} ]]; then
LOGE "文件夹 ${binFolder} 不存在！"
LOGI "制作 bin 文件夹：${binFolder}..."
mkdir -p ${binFolder}
fi
systemctl stop x-ui
cd ${binFolder}
rm -f geoip.dat geosite.dat geoip_IR.dat geosite_IR.dat geoip_VN.dat geosite_VN.dat
wget -N https://github.com/Loyalsoldier/v2ray-rules-dat/releases/latest/download/geoip.dat
wget -N https://github.com/Loyalsoldier/v2ray-rules-dat/releases/latest/download/geosite.dat
wget -O geoip_IR.dat -N https://github.com/chocolate4u/Iran-v2ray-rules/releases/latest/download/geoip.dat
wget -O geosite_IR.dat -N https://github.com/chocolate4u/Iran-v2ray-rules/releases/latest/download/geosite.dat
wget -O geoip_VN.dat https://github.com/vuong2023/vn-v2ray-rules/releases/latest/download/geoip.dat
wget -O geosite_VN.dat https://github.com/vuong2023/vn-v2ray-rules/releases/latest/download/geosite.dat
systemctl start x-ui
echo -e "${green}Geosite.dat + Geoip.dat + geoip_IR.dat + geosite_IR.dat 在 bin 文件夹: '${binfolder}' 中已经更新成功 !${plain}"
before_show_menu
}
install_acme() {
cd ~
LOGI "install acme..."
curl https://get.acme.sh | sh
if [ $? -ne 0 ]; then
LOGE "安装 acme 失败"
return 1
else
LOGI "安装 acme 成功"
fi
return 0
}
ssl_cert_issue_main() {
echo -e "${green}\t1.${plain} 获取 SSL 证书"
echo -e "${green}\t2.${plain} 吊销证书"
echo -e "${green}\t3.${plain} 续签证书"
echo -e "${green}\t0.${plain} 返回主菜单"
read -p "请输入选项: " choice
case "$choice" in
0)
show_menu
;;
1)
ssl_cert_issue
;;
2)
local domain=""
read -p "请输入您的域名以吊销证书: " domain
~/.acme.sh/acme.sh --revoke -d ${domain}
LOGI "证书吊销成功"
;;
3)
local domain=""
read -p "请输入您的域名以续签 SSL 证书: " domain
~/.acme.sh/acme.sh --renew -d ${domain} --force
;;
*) echo "无效选项" ;;
esac
}
ssl_cert_issue() {
# check for acme.sh first
if ! command -v ~/.acme.sh/acme.sh &>/dev/null; then
echo "未找到 acme.sh, 正在安装"
install_acme
if [ $? -ne 0 ]; then
LOGE "安装 acme 失败，请检查日志"
exit 1
fi
fi
# install socat second
case "${release}" in
ubuntu | debian | armbian)
apt update && apt install socat -y
;;
centos | almalinux | rocky | oracle)
yum -y update && yum -y install socat
;;
fedora)
dnf -y update && dnf -y install socat
;;
arch | manjaro)
pacman -Sy --noconfirm socat
;;
*)
echo -e "${red}不支持的操作系统，请检查脚本并手动安装必要的软件包。${plain}\n"
exit 1
;;
esac
if [ $? -ne 0 ]; then
LOGE "安装 socat 失败，请检查日志"
exit 1
else
LOGI "安装 socat 成功..."
fi
# get the domain here,and we need verify it
local domain=""
read -p "请输入您的域名:" domain
LOGD "您的域名是：${domain}，正在检查..."
# here we need to judge whether there exists cert already
local currentCert=$(~/.acme.sh/acme.sh --list | tail -1 | awk '{print $1}')
if [ ${currentCert} == ${domain} ]; then
local certInfo=$(~/.acme.sh/acme.sh --list)
LOGE "系统已经有证书，无法再次颁发，当前证书详细信息:"
LOGI "$certInfo"
exit 1
else
LOGI "您的域现在已准备好颁发证书..."
fi
# create a directory for install cert
certPath="/root/cert/${domain}"
if [ ! -d "$certPath" ]; then
mkdir -p "$certPath"
else
rm -rf "$certPath"
mkdir -p "$certPath"
fi
# get needed port here
local WebPort=80
read -p "请选择您使用的端口，默认为 80 端口:" WebPort
if [[ ${WebPort} -gt 65535 || ${WebPort} -lt 1 ]]; then
LOGE "您输入的端口 ${WebPort} 无效，将使用默认端口"
fi
LOGI "将使用端口：${WebPort} 来颁发证书，请确保该端口已开启..."
# NOTE:This should be handled by user
# open the port and kill the occupied progress
~/.acme.sh/acme.sh --set-default-ca --server letsencrypt
~/.acme.sh/acme.sh --issue -d ${domain} --standalone --httpport ${WebPort}
if [ $? -ne 0 ]; then
LOGE "颁发证书失败，请检查日志"
rm -rf ~/.acme.sh/${domain}
exit 1
else
LOGE "颁发证书成功，安装证书..."
fi
# install cert
~/.acme.sh/acme.sh --installcert -d ${domain} \
--key-file /root/cert/${domain}/privkey.pem \
--fullchain-file /root/cert/${domain}/fullchain.pem
if [ $? -ne 0 ]; then
LOGE "安装证书失败"
rm -rf ~/.acme.sh/${domain}
exit 1
else
LOGI "安装证书成功，启用自动续订..."
fi
~/.acme.sh/acme.sh --upgrade --auto-upgrade
if [ $? -ne 0 ]; then
LOGE "自动续订失败，证书详细信息:"
ls -lah cert/*
chmod 755 $certPath/*
exit 1
else
LOGI "自动续订成功，证书详细信息:"
ls -lah cert/*
chmod 755 $certPath/*
fi
}
ssl_cert_issue_CF() {
echo -E ""
LOGD "******使用说明******"
LOGI "此 Acme 脚本需要以下数据："
LOGI "1. Cloudflare 注册邮箱"
LOGI "2. Cloudflare 全局 API 密钥"
LOGI "3. Cloudflare 已解析 dns 到当前服务器的域名"
LOGI "4. 脚本申请证书，默认安装路径为 /root/cert "
confirm "确认申请? [y/n]" "y"
if [ $? -eq 0 ]; then
# check for acme.sh first
if ! command -v ~/.acme.sh/acme.sh &>/dev/null; then
echo "未找到 acme.sh, 正在安装"
install_acme
if [ $? -ne 0 ]; then
LOGE "安装 acme 失败，请检查日志"
exit 1
fi
fi
CF_Domain=""
CF_GlobalKey=""
CF_AccountEmail=""
certPath=/root/cert
if [ ! -d "$certPath" ]; then
mkdir $certPath
else
rm -rf $certPath
mkdir $certPath
fi
LOGD "请设置域名:"
read -p "在此输入您的域名:" CF_Domain
LOGD "您的域名为: ${CF_Domain}"
LOGD "请设置 CF Global API Key:"
read -p "在此输入您的 API Key:" CF_GlobalKey
LOGD "您的 API 密钥是: ${CF_GlobalKey}"
LOGD "请设置注册邮箱:"
read -p "在此输入您的邮箱:" CF_AccountEmail
LOGD "您的账号邮箱地址是: ${CF_AccountEmail}"
~/.acme.sh/acme.sh --set-default-ca --server letsencrypt
if [ $? -ne 0 ]; then
LOGE "默认 CA: Lets'Encrypt 失败，脚本退出..."
exit 1
fi
export CF_Key="${CF_GlobalKey}"
export CF_Email=${CF_AccountEmail}
~/.acme.sh/acme.sh --issue --dns dns_cf -d ${CF_Domain} -d *.${CF_Domain} --log
if [ $? -ne 0 ]; then
LOGE "证书颁发失败，脚本退出..."
exit 1
else
LOGI "证书颁发成功，正在安装..."
fi
~/.acme.sh/acme.sh --installcert -d ${CF_Domain} -d *.${CF_Domain} --ca-file /root/cert/ca.cer \
--cert-file /root/cert/${CF_Domain}.cer --key-file /root/cert/${CF_Domain}.key \
--fullchain-file /root/cert/fullchain.cer
if [ $? -ne 0 ]; then
LOGE "证书安装失败，脚本退出..."
exit 1
else
LOGI "证书安装成功，开启自动更新..."
fi
~/.acme.sh/acme.sh --upgrade --auto-upgrade
if [ $? -ne 0 ]; then
LOGE "自动更新设置失败，脚本退出..."
ls -lah cert
chmod 755 $certPath
exit 1
else
LOGI "证书已安装并开启自动续订，具体信息如下:"
ls -lah cert
chmod 755 $certPath
fi
else
show_menu
fi
}
warp_cloudflare() {
echo -e "${green}\t1.${plain} 安装 WARP socks5 代理"
echo -e "${green}\t2.${plain} 账户类型 (free, plus, team)"
echo -e "${green}\t3.${plain} 开启 / 关闭 WireProxy"
echo -e "${green}\t4.${plain} 卸载 WARP"
echo -e "${green}\t0.${plain} 返回主菜单"
read -p "请输入选项: " choice
case "$choice" in
0)
show_menu
;;
1)
bash <(curl -sSL https://raw.githubusercontent.com/hamid-gh98/x-ui-scripts/main/install_warp_proxy.sh)
;;
2)
warp a
;;
3)
warp y
;;
4)
warp u
;;
*) echo "无效选项" ;;
esac
}
run_speedtest() {
# Check if Speedtest is already installed
if ! command -v speedtest &>/dev/null; then
# If not installed, install it
local pkg_manager=""
local speedtest_install_script=""
if command -v dnf &>/dev/null; then
pkg_manager="dnf"
speedtest_install_script="https://packagecloud.io/install/repositories/ookla/speedtest-cli/script.rpm.sh"
elif command -v yum &>/dev/null; then
pkg_manager="yum"
speedtest_install_script="https://packagecloud.io/install/repositories/ookla/speedtest-cli/script.rpm.sh"
elif command -v apt-get &>/dev/null; then
pkg_manager="apt-get"
speedtest_install_script="https://packagecloud.io/install/repositories/ookla/speedtest-cli/script.deb.sh"
elif command -v apt &>/dev/null; then
pkg_manager="apt"
speedtest_install_script="https://packagecloud.io/install/repositories/ookla/speedtest-cli/script.deb.sh"
fi
if [[ -z $pkg_manager ]]; then
echo "错误：找不到包管理器。 您可能需要手动安装 Speedtest"
return 1
else
curl -s $speedtest_install_script | bash
$pkg_manager install -y speedtest
fi
fi
# Run Speedtest
speedtest
}
create_iplimit_jails() {
# Use default bantime if not passed => 15 minutes
local bantime="${1:-15}"
# Uncomment 'allowipv6 = auto' in fail2ban.conf
sed -i 's/#allowipv6 = auto/allowipv6 = auto/g' /etc/fail2ban/fail2ban.conf
#On Debian 12+ fail2ban's default backend should be changed to systemd
if [[ "${release}" == "debian" && ${os_version} -ge 12 ]]; then
sed -i '0,/action =/s/backend = auto/backend = systemd/' /etc/fail2ban/jail.conf
fi
cat << EOF > /etc/fail2ban/jail.d/3x-ipl.conf
[3x-ipl]
enabled=true
backend=auto
filter=3x-ipl
action=3x-ipl
logpath=${iplimit_log_path}
maxretry=2
findtime=32
bantime=${bantime}m
EOF
cat << EOF > /etc/fail2ban/filter.d/3x-ipl.conf