README of the RZ/G2 Flash Writer

Renesas Electronics Corporation

Aug-17-2020

The RZ/G2 flash writer is sample software for Renesas RZ/G2 Group MPUs. The RZ/G2 flash writer downloads binary images from Host PC via SCIF or USB and writes those binary images to Serial NOR Flash or eMMC.

1. Overview

This document explains about the RZ/G2 flash writer sample software for Renesas RZ/G2 Group MPUs.

The RZ/G2 flash writer is downloaded from the Host PC via SCIF or USB by the boot ROM container within the RZ/G2 device.

The RZ/G2 flash writer downloads binary images from Host PC via SCIF or USB, and writes those binary images to Serial NOR Flash (hereafter referred to as “Serial Flash”) or eMMC.

The RZ/G2 flash writer's Serial Flash writing support is for on-board Serial NOR Flash devices (i.e. W25M512JW and others).

The RZ/G2 flash writer eMMC writing support is for High Speed SDR (i.e. 50MHz) and x8 bus width mode.

Chapter 2 describes the operating environment.

Chapter 3 describes the software.

Chapter 4 explains example of how to build the RZ/G2 flash writer.

Chapter 5 explains example of how to perform the RZ/G2 flash writer.

Chapter 6 explains how to handle error case.

Chapter 7 explains revision history.

Note) This sample software does not support file systems. Therefore, only raw binary images can be downloaded and programmed into Serial NOR Flash or eMMC.

1.2. License

BSD-3-Clause (please see file LICENSE.md for the details)

1.3. Notice

The RZ/G2 flash writer is distributed as a sample software from Renesas without any warranty or support.

1.4. Contributing

To contribute to this software, you should email patches to renesas-rz@renesas.com. Please send .patch files as email attachments, not embedded in the email body.

1.5. References

The following table shows the document related to this function.

2. Operating Environment

2.1. Hardware Environment

The following table lists the hardware needed to use this utility.

Hardware environment

Name	Note
Target board	Hoperun HiHope RZ/G2[M,N,H] platform
	Silicon Linux RZ/G2E evaluation kit (EK874)
Host PC	Ubuntu Desktop 14.04(64bit) or later

The following table shows Serial Flash and eMMC support for each MPU.

Serial Flash / eMMC support status of each MPU

MPU	Read/Write the Serial Flash	Boot from the Serial Flash	Read/Write the eMMC	Boot from the eMMC	MMC interface
RZ/G2H	Support	Support	Support	Support	MMC1
RZ/G2M	Support	Support	Support	Support *1	MMC1
RZ/G2N	Support	Support	Support	Support	MMC1
RZ/G2E	Support	Support	Support *2	Support *2	MMC1

*1: Some early samples are not support booting from the eMMC. Please contact to Renesas sales for further details.

*2: eMMC is not implemented on the Silicon Linux RZ/G2E evaluation kit Rev.A - C boards. Rev.D or later boards can use eMMC, but note that the support is disabled in default settings.

2.2. Software Environment

The following table lists the software required to use this sample software.

Software environment

Name	Note
Linaro Toolchain *1	Linaro Binary Toolchain Release GCC 7.3-2018.05 for aarch64-elf.
Yocto SDK 1 2	Yocto SDK built from Yocto environment for RZ/G2 Group

*1: One of the above toolchains are required.

*2: Regarding how to get the Yocto SDK, refer to Related Document No.2 or No.3.

3. Software

3.1. Function

This package has the following capabilities:

Write binary images to the Serial Flash.
Erase the Serial Flash.
Display the CID/CSD/EXT_CSD registers of an eMMC.
Modify the EXT_CSD registers of an eMMC.
Write binary images to the boot partition of an eMMC.
Write binary images to the user data area of an eMMC.
Erase the boot partition of an eMMC.
Erase the user data area of an eMMC.
Change the SCIF baud rate setting.
Display the command help.

3.3. Option setting

The RZ/G2 flash writer support the following build options.

3.3.2. BOARD

Select from the following table according to the board settings.

If this option is not selected, the default value is HIHOPE.

BOARD	BOARD setting
HIHOPE	Generate binary that works on Hoperun HiHope RZ/G2[MN] platform. (default)
EK874	Generate binary that works on Silicon Linux RZ/G2E evaluation kit.

3.3.5. SERIAL_FLASH

Select from the following table according to the Serial Flash writing function.

If this option is not selected, the default value is ENABLE.

Association table for the SERIAL_FLASH value and valid Serial Flash writing function settings

SERIAL_FLASH	Serial Flash writing setting
ENABLE	Serial Flash writing function is available. (default)
DISABLE	Serial Flash writing function is not available.

3.3.6 eMMC

Select from the following table according to the eMMC writing function.

If this option is not selected, the default value is ENABLE.

Association table for the eMMC value and valid eMMC writing function settings

EMMC	Serial Flash writing setting
ENABLE	eMMC writing function is available. (default for HIHOPE)
DISABLE	eMMC writing function is not available. (default for EK874)

3.3.7 USB

Select from the following table according to the USB download mode support.

If this option is not selected, the default value is ENABLE.

Association table for the USB communications values

USB	USB Communications
ENABLE	USB communication to Host PC is available. (default for HIHOPE)
DISABLE	USB communication to Host PC is not available. (default for EK874)

3.4. Command specification

The following table shows the command list.

Command list

Command	Description
XLS2	Write the S-record format images to the Serial Flash.
XCS	Erase the Serial Flash.
EM_DCID	Display the CID registers of eMMC.
EM_DCSD	Display the CSD registers of eMMC.
EM_DECSD	Display the EXT_CSD registers of eMMC.
EM_SECSD	Modify the EXT_CSD registers of eMMC.
EM_W	Write to the S-record format images to the user data area of eMMC, and the boot partition of eMMC.
EM_WB	Write to the raw binary images to the user data area of eMMC, and the boot partition of eMMC.
EM_E	Erase the user data area of eMMC, and the boot partition of eMMC.
SUP	Change the SCIF baud rate setting.
RESET	Perform RESET of the CPU.
H	Display the command help.

3.4.1. Write to the S-record format images to the Serial Flash

This command writes the S-record format image to Serial Flash.

Example of writing data for the Serial Flash boot

Filename	Program Top Address	Flash Save Address	Description
bootparam_sa0.srec	H'E6320000	H'000000	Loader(Boot parameter)
bl2-`<board_name>`.srec	H'E6304000	H'040000	Loader
cert_header_sa6.srec	H'E6320000	H'180000	Loader(Certification)
bl31-`<board_name>`.srec	H'44000000	H'1C0000	ARM Trusted Firmware
u-boot-elf-`<board_name>`.srec	H'50000000	H'300000	U-boot

The following shows the procedure of this command. The values must be entered as hexadecimal.

Note) The following procedure is an example on HiHope RZ/G2M board.

Note) If Flash is already blank, you will not be asked to erase

>XLS2
===== Qspi writing of RZ/G2 Board Command =============
Load Program to Spiflash
Writes to any of SPI address.
 Winbond : W25M512JW
Program Top Address & Qspi Save Address
===== Please Input Program Top Address ============
  Please Input : H'e6304000                                             <<<< Enter "e6304000" here

===== Please Input Qspi Save Address ===
  Please Input : H'40000                                                <<<< Enter "40000" here
SPI Data Clear(H'FF) Check :H'00040000-0005FFFF,Clear OK?(y/n)          <<<< Enter "y" here
Work RAM(H'50000000-H'53FFFFFF) Clear....
please send ! ('.' & CR stop load)
SPI Data Clear(H'FF) Check :H'00040000-0005FFFF Erasing...Erase Completed
SAVE SPI-FLASH.......
======= Qspi  Save Information  =================
 SpiFlashMemory Stat Address : H'00040000
 SpiFlashMemory End Address  : H'0005B0E3
===========================================================
>

Image writing has been completed.

3.4.3. Erase the Serial NOR Flash

This command erases all sectors of Serial Flash.

The following shows the procedure of this command.

Note) The following procedure is an example on HiHope RZ/G2M board.

>XCS
ALL ERASE SpiFlash memory
Clear OK?(y/n)

Please enter the 'y' key.

>XCS
ALL ERASE SpiFlash memory
 Winbond : W25M512JW
 ERASE QSPI-FLASH (60sec[typ]).... complete!
>

Selected Serial Flash has been erased.

3.4.4. Display the CID registers command

This command displays the contents of the CID registers of the eMMC.

The following shows the procedure of this command.

EM_DCID

[CID Field Data]
[127:120]  MID  0x13
[113:112]  CBX  0x01
[111:104]  OID  0x4E
[103: 56]  PNM  0x52314A35374C
[ 55: 48]  PRV  0x10
[ 47: 16]  PSN  0x18E3D660
[ 15:  8]  MDT  0x73
[  7:  1]  CRC  0x00

3.4.5. Display the CSD registers command

This command displays the contents of the CSD registers of eMMC.

The following shows the procedure of this command.

>EM_DCSD

[CSD Field Data]
[127:126]  CSD_STRUCTURE       0x03
[125:122]  SPEC_VERS           0x04
[119:112]  TAAC                0x7F
...
[ 11: 10]  FILE_FORMAT         0x00
[  9:  8]  ECC                 0x00
[  7:  1]  CRC                 0x00

3.4.6. Display the EXT_CSD registers command

This command displays the contents of the EXT_CSD registers of the eMMC.

The following shows the procedure of this command.

>EM_DECSD

[EXT_CSD Field Data]
[505:505]  EXT_SECURITY_ERR                           0x00
[504:504]  S_CMD_SET                                  0x01
[503:503]  HPI_FEATURES                               0x01
...
[142:140]  ENH_SIZE_MULT                              0x000000
[139:136]  ENH_START_ADDR                             0x00000000
[134:134]  SEC_BAD_BLK_MGMNT                          0x00

3.4.7. Modify the EXT_CSD registers of eMMC command

This command modifies the contents of the EXT_CSD registers in the eMMC.

The values must be entered as hexadecimal.

Example:

>EM_SECSD
  Please Input EXT_CSD Index(H'00 - H'1FF) :b1
  EXT_CSD[B1] = 0x00
  Please Input Value(H'00 - H'FF) :a
  EXT_CSD[B1] = 0x0A

eMMC Boot Settings

Please note that for eMMC booting, the following EXT_CSD registers need to be modified:

EXT_CSD[B1] = 0x0A
EXT_CSD[B3] = 0x08

3.4.8. Write to the S-record format images to the eMMC

This command writes the S-record format image to any partition of the eMMC.

Example of writing data for the eMMC boot

Filename	Program Top Address	eMMC Save Partition	eMMC Save Sectors	Description
bootparam_sa0.srec	H'E6320000	boot partition1	H'000000	Loader(Boot parameter)
bl2-`<board_name>`.srec	H'E6304000	boot partition1	H'00001E	Loader
cert_header_sa6.srec	H'E6320000	boot partition1	H'000180	Loader(Certification)
bl31-`<board_name>`.srec	H'44000000	boot partition1	H'000200	ARM Trusted Firmware
u-boot-elf-`<board_name>`.srec	H'50000000	boot partition2	H'000000	U-boot

The following shows the procedure of this command. The values must be entered as hexadecimal. Please enter the start sector number of the write image in hexadecimal. Sector size is 512 bytes. Please enter the program top address of the write image in hexadecimal. Please download the write image in S-record format.

>EM_W
EM_W Start --------------
---------------------------------------------------------
Please select,eMMC Partition Area.
 0:User Partition Area   : 30535680 KBytes
  eMMC Sector Cnt : H'0 - H'03A3DFFF
 1:Boot Partition 1      : 16384 KBytes
  eMMC Sector Cnt : H'0 - H'00007FFF
 2:Boot Partition 2      : 16384 KBytes
  eMMC Sector Cnt : H'0 - H'00007FFF
---------------------------------------------------------
  Select area(0-2)>1                                         <<<< Enter "1" here
-- Boot Partition 1 Program -----------------------------
Please Input Start Address in sector :0000                   <<<< Enter "0000" here
Please Input Program Start Address : E6320000                <<<< Enter "E6320000" here
Work RAM(H'50000000-H'50FFFFFF) Clear....
please send ! ('.' & CR stop load)
SAVE -FLASH.......
EM_W Complete!

Image writing has been completed.

3.4.10. Erase the eMMC

This command erases any partition of the eMMC.

The following shows the procedure of this command.

>EM_E
EM_E Start --------------
---------------------------------------------------------
Please select,eMMC Partition Area.
 0:User Partition Area   : 30539776 KBytes
  eMMC Sector Cnt : H'0 - H'03A3FFFF
 1:Boot Partition 1      : 8192 KBytes
  eMMC Sector Cnt : H'0 - H'00003FFF
 2:Boot Partition 2      : 8192 KBytes
  eMMC Sector Cnt : H'0 - H'00003FFF
---------------------------------------------------------
  Select area(0-2)>0                                      <<<< Enter "0" here
-- User Partition Area Program --------------------------
EM_E Complete!

Selected partition has been erased.

3.4.11. Change the SCIF baud rate setting

This command will change the baud rate of the SCIF.

Baud rate depends on the MPU and the SCIF clock setting on the board.

Baud rate settings after command execution

Board	Baud rate at startup	Baud rate at After command execution
HIHOPE, EK874	115200bps	921600bps

Note) The baud rate that has been changed in this command cannot be undone until the power is turned off.

The following shows the procedure of this command.

>SUP
Scif speed UP
Please change to 921.6Kbps baud rate setting of the terminal.

3.4.12. Display the command help

Displays a description of the commands.

The following shows the procedure of this command.

>H
        HyperFlash/SPI Flash write command
 XCS            erase program to HyperFlash/SPI Flash
 XLS2           write program to HyperFlash/SPI Flash
 XLS3           write program to HyperFlash/SPI Flash(Binary)

        eMMC write command
 EM_DCID        display register CID
 EM_DCSD        display register CSD
 EM_DECSD       display register EXT_CSD
 EM_SECSD       change register EXT_CSD byte
 EM_W           write program to eMMC
 EM_WB          write program to eMMC (Binary)
 EM_E           erase program to eMMC
 SUP            Scif speed UP (Change to speed up baud rate setting)
 H              help
>

4. How to build the RZ/G2 flash writer

This chapter is described how to build the RZ/G2 flash writer. Command is executed in the user's home directory (~ /).

4.1. Prepare the compiler

Gets cross compiler for linaro or setup the Yocto SDK.

Linaro toolchain:

cd ~/
wget https://releases.linaro.org/components/toolchain/binaries/7.3-2018.05/aarch64-elf/gcc-linaro-7.3.1-2018.05-x86_64_aarch64-elf.tar.xz
tar xvf gcc-linaro-7.3.1-2018.05-x86_64_aarch64-elf.tar.xz

Yocto SDK:

source /opt/poky/2.4.3/environment-setup-aarch64-poky-linux

4.2. Prepare the source code

Get the source code of RZ/G2 flash writer.

cd ~/
git clone https://github.com/renesas-rz/rzg2_flash_writer.git
cd rzg2_flash_writer
git checkout -b v1.05 v1.05

4.3. Build the RZ/G2 flash writer

S-record file will be built by the following command.

Linaro toolchain:

make -f makefile.linaro clean
CROSS_COMPILE=~/gcc-linaro-7.3.1-2018.05-x86_64_aarch64-elf/bin/aarch64-elf- make -f makefile.linaro BOARD=HIHOPE

Note) Makefile for linaro toolchain is changed from makefile to makefile.linaro at v1.01.

Yocto SDK:

make clean
make BOARD=HIHOPE

Output image will be available in the following directory.

./AArch64_output/AArch64_Flash_writer_SCIF_DUMMY_CERT_E6300400_hihope.mot

The target file name changes depending on the build options.

The following table lists the relationship between build option and target files.

Description of build options and target files

Build options	Target filename
HIHOPE	AArch64_Flash_writer_SCIF_DUMMY_CERT_E6300400_hihope.mot
EK874	AArch64_Flash_writer_SCIF_DUMMY_CERT_E6300400_ek874.mot

5. How to run the RZ/G2 flash writer

5.1. Prepare for write to the Serial Flash and eMMC

Start the target in the SCIF download mode and run the RZ/G2 flash writer sample code.

Regarding the DIP switch configuration on the board, refer to Related Document No.4.

The following table shows the setting of terminal software.

Terminal software configuration

Baud rate	Data bit length	Parity check	Stop bits	Flow control
115200bps	8bits	none	1bit	none

Terminal software outputs the following log at power ON the target.

SCIF Download mode (w/o verification)
(C) Renesas Electronics Corp.

-- Load Program to SystemRAM ---------------
please send !

Transfer S-record file after the log output.

S-record file:

AArch64_output/AArch64_Flash_writer_SCIF_DUMMY_CERT_E6300400_<board_name>.mot

After the transfer has succeeded, the following log will be shown.

Flash writer for RZ/G2M V1.01 Jan.08,2020
>

Please enter the any key from the console to continue.

For details on how to write to the Serial Flash and eMMC, please refer to Section 3.4.

5.2. Prepare for boot from the Serial Flash and eMMC

To boot from the eMMC, need to change the DIP switch setting.

Regarding the DIP switch configuration on the board, refer to Related Document No.4.

6. Error case to handle

6.1. EXT_CSD incorrect setting case

If error of eMMC command is occurred, please check the following description and restart.

Please Check the correct setting of EXT_CSD. If the wrong setting is present, to set the correct setting using EM_SECSD command.
Program start address error of S-record file.

The following shows the setting of High speed SDR(50MHz) x8 bus width mode, Boot partition 1 enable.

Address	Register Name	Filed name	Bit filed	Settings
EXT_CSD[179]	PARTITION_CONFIG	BOOT_ACK	[6]	0x0
		BOOT_PARTITION_ENABLE	[5:3]	0x1
EXT_CSD[177]	BOOT_BUS_CONDITIONS	BOOT_MODE	[4:3]	0x1
		BOOT_BUS_WIDTH	[1:0]	0x2

For details of EXT_CSD, please refer to Related Document No.1.

6.2. Program start address error of S-record format file

After the message "Please Input User Program Start Address" has been displayed, input a start address of the S-record format file to be loaded (smallest value) as the start address of the program. (This address is treated as the start address and branch address of the data transfer destination from the eMMC device in the program.)

Please check the program start address and write again program using EM_W command.

7. Revision history

Describe the revision history of RZ/G2 flash writer.

7.1. v1.00

First release.

7.2. v1.01

Support HiHope RZ/G2[MN] Rev.3/Rev.4 boards
Improve makefile to support the build by bitbake
Add new makefile for the linaro toolchain build

7.3. v1.02

Support HiHope RZ/G2[H] Rev.4 boards
Support USB Download mode
List register configurations needed eMMC boot

7.4. v1.03

Support QSPI Flash devices smaller than 16MB

7.5. v1.04

Support SiLinux EK874 Rev.D/Rev.E boards

7.6. v1.05

Update DDR initialization sequences
Support the RESET command

Name		Name	Last commit message	Last commit date
Latest commit History 18 Commits
AArch64_boot		AArch64_boot
AArch64_lib		AArch64_lib
ddr		ddr
include		include
.gitignore		.gitignore
LICENSE.md		LICENSE.md
Message.c		Message.c
README.md		README.md
boardid.c		boardid.c
boot_init_gpio.c		boot_init_gpio.c
boot_init_lbsc.c		boot_init_lbsc.c
boot_init_port.c		boot_init_port.c
cert_param.c		cert_param.c
common.c		common.c
cpudrv.c		cpudrv.c
ddrcheck.c		ddrcheck.c
devdrv.c		devdrv.c
dg_emmc_access.c		dg_emmc_access.c
dg_emmc_config.c		dg_emmc_config.c
dgmodul1.c		dgmodul1.c
dgmodul4.c		dgmodul4.c
dgtable.c		dgtable.c
dmaspi.c		dmaspi.c
emmc_cmd.c		emmc_cmd.c
emmc_erase.c		emmc_erase.c
emmc_init.c		emmc_init.c
emmc_interrupt.c		emmc_interrupt.c
emmc_mount.c		emmc_mount.c
emmc_utility.c		emmc_utility.c
emmc_write.c		emmc_write.c
init_scif.c		init_scif.c
main.c		main.c
makefile		makefile
makefile.linaro		makefile.linaro
memory_writer.def		memory_writer.def
memory_writer_small.def		memory_writer_small.def
memory_writer_small_with_cert.def		memory_writer_small_with_cert.def
memory_writer_with_cert.def		memory_writer_with_cert.def
micro_wait.c		micro_wait.c
ramckmdl.c		ramckmdl.c
rpcqspidrv.c		rpcqspidrv.c
scifdrv.c		scifdrv.c
spiflash1drv.c		spiflash1drv.c

Number	Issuer	Title	Edition
1	JEDEC	Embedded Multi-Media Card (eMMC) Electrical Standard (5.01)	JESD84-B50.1
2	Renesas	Release Note for Verified Linux Package for 64bit kernel	Rev.1.01 or later
3	Renesas	RZ/G2 Yocto recipe Start-Up Guide	Rev.1.01 or later
4	Renesas	RZ/G2 Reference Boards Start-up Guide	Rev.1.01 or later

License

Scalys/rzg2_flash_writer

Folders and files

Latest commit

History

Repository files navigation

README of the RZ/G2 Flash Writer

1. Overview

1.2. License

1.3. Notice

1.4. Contributing

1.5. References

Related Document

2. Operating Environment

2.1. Hardware Environment

Hardware environment

Serial Flash / eMMC support status of each MPU

2.2. Software Environment

Software environment

3. Software

3.1. Function

3.3. Option setting

3.3.2. BOARD

3.3.5. SERIAL_FLASH

Association table for the SERIAL_FLASH value and valid Serial Flash writing function settings

3.3.6 eMMC

Association table for the eMMC value and valid eMMC writing function settings

3.3.7 USB

Association table for the USB communications values

3.4. Command specification

Command list

3.4.1. Write to the S-record format images to the Serial Flash

Example of writing data for the Serial Flash boot

3.4.3. Erase the Serial NOR Flash

3.4.4. Display the CID registers command

3.4.5. Display the CSD registers command

3.4.6. Display the EXT_CSD registers command

3.4.7. Modify the EXT_CSD registers of eMMC command

eMMC Boot Settings

3.4.8. Write to the S-record format images to the eMMC

Example of writing data for the eMMC boot

3.4.10. Erase the eMMC

3.4.11. Change the SCIF baud rate setting

Baud rate settings after command execution

3.4.12. Display the command help

4. How to build the RZ/G2 flash writer

4.1. Prepare the compiler

4.2. Prepare the source code

4.3. Build the RZ/G2 flash writer

Description of build options and target files

5. How to run the RZ/G2 flash writer

5.1. Prepare for write to the Serial Flash and eMMC

Terminal software configuration

5.2. Prepare for boot from the Serial Flash and eMMC

6. Error case to handle

6.1. EXT_CSD incorrect setting case

6.2. Program start address error of S-record format file

7. Revision history

7.1. v1.00

7.2. v1.01

7.3. v1.02

7.4. v1.03

7.5. v1.04

7.6. v1.05

About

Resources

License

Stars

Watchers

Forks

Releases

Packages 0

Languages

Packages