GitHub - VitalyVaryvdin/rtsp-simple-server: ready-to-use RTSP / RTMP / LL-HLS / WebRTC server and proxy that allows to read, publish and proxy video and audio streams

rtsp-simple-server / MediaMTX is a ready-to-use and zero-dependency server and proxy that allows users to publish, read and proxy live video and audio streams.

Live streams can be published to the server with:

protocol	variants	codecs
RTSP clients (FFmpeg, GStreamer, etc)	UDP, TCP, RTSPS	H264, H265, VP8, VP9, AV1, MPEG2, M-JPEG, MP3, MPEG4 Audio (AAC), Opus, G711, G722, LPCM and any RTP-compatible codec
RTSP servers and cameras	UDP, UDP-Multicast, TCP, RTSPS	H264, H265, VP8, VP9, AV1, MPEG2, M-JPEG, MP3, MPEG4 Audio (AAC), Opus, G711, G722, LPCM and any RTP-compatible codec
RTMP clients (OBS Studio)	RTMP, RTMPS	H264, H265, MPEG4 Audio (AAC)
RTMP servers and cameras	RTMP, RTMPS	H264, MPEG4 Audio (AAC)
HLS servers and cameras	Low-Latency HLS, MP4-based HLS, legacy HLS	H264, H265, MPEG4 Audio (AAC), Opus
Raspberry Pi Cameras		H264

And can be read from the server with:

protocol	variants	codecs
RTSP	UDP, UDP-Multicast, TCP, RTSPS	H264, H265, VP8, VP9, AV1, MPEG2, M-JPEG, MP3, MPEG4 Audio (AAC), Opus, G711, G722, LPCM and any RTP-compatible codec
RTMP	RTMP, RTMPS	H264, MPEG4 Audio (AAC)
HLS	Low-Latency HLS, MP4-based HLS, legacy HLS	H264, H265, MPEG4 Audio (AAC), Opus
WebRTC		H264, VP8, VP9, Opus, G711, G722

Features:

Publish live streams to the server
Read live streams from the server
Proxy streams from other servers or cameras, always or on-demand
Streams are automatically converted from a protocol to another. For instance, it's possible to publish a stream with RTSP and read it with HLS
Serve multiple streams at once in separate paths
Authenticate users; use internal or external authentication
Redirect readers to other RTSP servers (load balancing)
Query and control the server through an HTTP API
Reload the configuration without disconnecting existing clients (hot reloading)
Read Prometheus-compatible metrics
Run external commands when clients connect, disconnect, read or publish streams
Natively compatible with the Raspberry Pi Camera
Compatible with Linux, Windows and macOS, does not require any dependency or interpreter, it's a single executable

Important announcement

rtsp-simple-server is being rebranded as MediaMTX. The reason is pretty obvious: this project started as a RTSP server but has evolved into a much more versatile media server (i like to call it a "media broker", a message broker for media streams), that is not tied to the RTSP protocol anymore. Nothing will change regarding license, features and backward compatibility.

Furthermore, my main open source projects are being transferred to the bluenviron organization, in order to allow the community to maintain and evolve the code regardless of my personal availability.

In the next months, the repository name and the docker image name will be changed accordingly.

Installation

Standard

Download and extract a precompiled binary from the release page.
Start the server:
```
./rtsp-simple-server
```

Docker

Download and launch the image:

docker run --rm -it --network=host aler9/rtsp-simple-server

The --network=host flag is mandatory since Docker can change the source port of UDP packets for routing reasons, and this doesn't allow the server to find out the author of the packets. This issue can be avoided by disabling the UDP transport protocol:

docker run --rm -it -e RTSP_PROTOCOLS=tcp -p 8554:8554 -p 1935:1935 -p 8888:8888 -p 8889:8889 aler9/rtsp-simple-server

Please keep in mind that the Docker image doesn't include FFmpeg. if you need to use FFmpeg for an external command or anything else, you need to build a Docker image that contains both rtsp-simple-server and FFmpeg, by following instructions here.

OpenWRT

In a x86 Linux system, download the OpenWRT SDK corresponding to the wanted OpenWRT version and target from the OpenWRT website and extract it.

Open a terminal in the SDK folder and setup the SDK:

./scripts/feeds update -a
./scripts/feeds install -a
make defconfig

Download the server Makefile and set the server version inside the file:

mkdir package/rtsp-simple-server
wget -O package/rtsp-simple-server/Makefile https://raw.githubusercontent.com/aler9/rtsp-simple-server/main/openwrt.mk
sed -i "s/v0.0.0/$(git ls-remote --tags --sort=v:refname https://github.com/aler9/rtsp-simple-server | tail -n1 | sed 's/.*\///; s/\^{}//')/" package/rtsp-simple-server/Makefile

Compile the server:

make package/rtsp-simple-server/compile -j$(nproc)

Transfer the .ipk file from bin/packages/*/base to the OpenWRT system and install it with:
```
opkg install [ipk-file-name].ipk
```

Basic usage

Publish a stream. For instance, you can publish a video/audio file with FFmpeg:

ffmpeg -re -stream_loop -1 -i file.ts -c copy -f rtsp rtsp://localhost:8554/mystream

or GStreamer:

gst-launch-1.0 rtspclientsink name=s location=rtsp://localhost:8554/mystream filesrc location=file.mp4 ! qtdemux name=d d.video_0 ! queue ! s.sink_0 d.audio_0 ! queue ! s.sink_1

To publish from other hardware / software, take a look at the Publish to the server section.

Open the stream. For instance, you can open the stream with VLC:

vlc --network-caching=50 rtsp://localhost:8554/mystream

or GStreamer:

gst-play-1.0 rtsp://localhost:8554/mystream

or FFmpeg:

ffmpeg -i rtsp://localhost:8554/mystream -c copy output.mp4

General

Configuration

All the configuration parameters are listed and commented in the configuration file.

There are 3 ways to change the configuration:

By editing the rtsp-simple-server.yml file, that is
- included into the release bundle
- available in the root folder of the Docker image (/rtsp-simple-server.yml); it can be overridden in this way:
```
docker run --rm -it --network=host -v $PWD/rtsp-simple-server.yml:/rtsp-simple-server.yml aler9/rtsp-simple-server
```
The configuration can be changed dynamically when the server is running (hot reloading) by writing to the configuration file. Changes are detected and applied without disconnecting existing clients, whenever it's possible.
By overriding configuration parameters with environment variables, in the format RTSP_PARAMNAME, where PARAMNAME is the uppercase name of a parameter. For instance, the rtspAddress parameter can be overridden in the following way:
```
RTSP_RTSPADDRESS="127.0.0.1:8554" ./rtsp-simple-server
```
Parameters that have array as value can be overriden by setting a comma-separated list. For example:
```
RTSP_PROTOCOLS="tcp,udp"
```
Parameters in maps can be overridden by using underscores, in the following way:
```
RTSP_PATHS_TEST_SOURCE=rtsp://myurl ./rtsp-simple-server
```
This method is particularly useful when using Docker; any configuration parameter can be changed by passing environment variables with the -e flag:
```
docker run --rm -it --network=host -e RTSP_PATHS_TEST_SOURCE=rtsp://myurl aler9/rtsp-simple-server
```
By using the HTTP API.

Authentication

Edit rtsp-simple-server.yml and replace everything inside section paths with the following content:

paths:
  all:
    publishUser: myuser
    publishPass: mypass

Only publishers that provide both username and password will be able to proceed:

ffmpeg -re -stream_loop -1 -i file.ts -c copy -f rtsp rtsp://myuser:mypass@localhost:8554/mystream

It's possible to setup authentication for readers too:

paths:
  all:
    publishUser: myuser
    publishPass: mypass

    readUser: user
    readPass: userpass

If storing plain credentials in the configuration file is a security problem, username and passwords can be stored as sha256-hashed strings; a string must be hashed with sha256 and encoded with base64:

echo -n "userpass" | openssl dgst -binary -sha256 | openssl base64

Then stored with the sha256: prefix:

paths:
  all:
    readUser: sha256:j1tsRqDEw9xvq/D7/9tMx6Jh/jMhk3UfjwIB2f1zgMo=
    readPass: sha256:BdSWkrdV+ZxFBLUQQY7+7uv9RmiSVA8nrPmjGjJtZQQ=

WARNING: enable encryption or use a VPN to ensure that no one is intercepting the credentials.

Authentication can be delegated to an external HTTP server:

externalAuthenticationURL: http://myauthserver/auth

Each time a user needs to be authenticated, the specified URL will be requested with the POST method and this payload:

{
  "ip": "ip",
  "user": "user",
  "password": "password",
  "path": "path",
  "protocol": "rtsp|rtmp|hls|webrtc",
  "id": "id",
  "action": "read|publish",
  "query": "query"
}

If the URL returns a status code that begins with 20 (i.e. 200), authentication is successful, otherwise it fails.

Please be aware that it's perfectly normal for the authentication server to receive requests with empty users and passwords, i.e.:

{
  "user": "",
  "password": "",
}

This happens because a RTSP client doesn't provide credentials until it is asked to. In order to receive the credentials, the authentication server must reply with status code 401 - the client will then send credentials.

Encrypt the configuration

The configuration file can be entirely encrypted for security purposes.

An online encryption tool is available here.

The encryption procedure is the following:

NaCL's crypto_secretbox function is applied to the content of the configuration. NaCL is a cryptographic library available for C/C++, Go, C# and many other languages;
The string is prefixed with the nonce;
The string is encoded with base64.

After performing the encryption, put the base64-encoded result into the configuration file, and launch the server with the RTSP_CONFKEY variable:

RTSP_CONFKEY=mykey ./rtsp-simple-server

Proxy mode

rtsp-simple-server is also a proxy, that is usually deployed in one of these scenarios:

when there are multiple users that are reading a stream and the bandwidth is limited; the proxy is used to receive the stream once. Users can then connect to the proxy instead of the original source.
when there's a NAT / firewall between a stream and the users; the proxy is installed on the NAT and makes the stream available to the outside world.

Edit rtsp-simple-server.yml and replace everything inside section paths with the following content:

paths:
  proxied:
    # url of the source stream, in the format rtsp://user:pass@host:port/path
    source: rtsp://original-url

After starting the server, users can connect to rtsp://localhost:8554/proxied, instead of connecting to the original url. The server supports any number of source streams, it's enough to add additional entries to the paths section:

paths:
  proxied1:
    source: rtsp://url1

  proxied2:
    source: rtsp://url1

It's possible to save bandwidth by enabling the on-demand mode: the stream will be pulled only when at least a client is connected:

paths:
  proxied:
    source: rtsp://original-url
    sourceOnDemand: yes

Remuxing, re-encoding, compression

To change the format, codec or compression of a stream, use FFmpeg or GStreamer together with rtsp-simple-server. For instance, to re-encode an existing stream, that is available in the /original path, and publish the resulting stream in the /compressed path, edit rtsp-simple-server.yml and replace everything inside section paths with the following content:

paths:
  all:
  original:
    runOnReady: ffmpeg -i rtsp://localhost:$RTSP_PORT/$RTSP_PATH -pix_fmt yuv420p -c:v libx264 -preset ultrafast -b:v 600k -max_muxing_queue_size 1024 -f rtsp rtsp://localhost:$RTSP_PORT/compressed
    runOnReadyRestart: yes

Save streams to disk

To save available streams to disk, you can use the runOnReady parameter and FFmpeg:

paths:
  mypath:
    runOnReady: ffmpeg -i rtsp://localhost:$RTSP_PORT/$RTSP_PATH -c copy -f segment -strftime 1 -segment_time 60 -segment_format mpegts saved_%Y-%m-%d_%H-%M-%S.ts
    runOnReadyRestart: yes

In the configuratio above, streams are saved into TS files, that can be read even if the system crashes, while MP4 files can't.

On-demand publishing

Edit rtsp-simple-server.yml and replace everything inside section paths with the following content:

paths:
  ondemand:
    runOnDemand: ffmpeg -re -stream_loop -1 -i file.ts -c copy -f rtsp rtsp://localhost:$RTSP_PORT/$RTSP_PATH
    runOnDemandRestart: yes

The command inserted into runOnDemand will start only when a client requests the path ondemand, therefore the file will start streaming only when requested.

Start on boot

Linux

Systemd is the service manager used by Ubuntu, Debian and many other Linux distributions, and allows to launch rtsp-simple-server on boot.

Download a release bundle from the release page, unzip it, and move the executable and configuration in the system:

sudo mv rtsp-simple-server /usr/local/bin/
sudo mv rtsp-simple-server.yml /usr/local/etc/

Create the service:

sudo tee /etc/systemd/system/rtsp-simple-server.service >/dev/null << EOF
[Unit]
Wants=network.target
[Service]
ExecStart=/usr/local/bin/rtsp-simple-server /usr/local/etc/rtsp-simple-server.yml
[Install]
WantedBy=multi-user.target
EOF

Enable and start the service:

sudo systemctl daemon-reload
sudo systemctl enable rtsp-simple-server
sudo systemctl start rtsp-simple-server

Windows

Download the WinSW v2 executable and place it into the same folder of rtsp-simple-server.exe.

In the same folder, create a file named WinSW-x64.xml with this content:

<service>
  <id>rtsp-simple-server</id>
  <name>rtsp-simple-server</name>
  <description></description>
  <executable>%BASE%/rtsp-simple-server.exe</executable>
</service>

Open a terminal, navigate to the folder and run:

WinSW-x64 install

The server is now installed as a system service and will start at boot time.

HTTP API

The server can be queried and controlled with an HTTP API, that must be enabled by setting the api parameter in the configuration:

api: yes

The API listens on apiAddress, that by default is 127.0.0.1:9997; for instance, to obtain a list of active paths, run:

curl http://127.0.0.1:9997/v1/paths/list

Full documentation of the API is available on the dedicated site.

Metrics

A metrics exporter, compatible with Prometheus, can be enabled with the parameter metrics: yes; then the server can be queried for metrics with Prometheus or with a simple HTTP request:

wget -qO- localhost:9998/metrics

Obtaining:

# metrics of every path
paths{name="[path_name]",state="[state]"} 1
paths_bytes_received{name="[path_name]",state="[state]"} 1234

# metrics of every HLS muxer
hls_muxers{name="[name]"} 1
hls_muxers_bytes_sent{name="[name]"} 187

# metrics of every RTSP connection
rtsp_conns{id="[id]"} 1
rtsp_conns_bytes_received{id="[id]"} 1234
rtsp_conns_bytes_sent{id="[id]"} 187

# metrics of every RTSP session
rtsp_sessions{id="[id]",state="idle"} 1
rtsp_sessions_bytes_received{id="[id]",state="[state]"} 1234
rtsp_sessions_bytes_sent{id="[id]",state="[state]"} 187

# metrics of every RTSPS connection
rtsps_conns{id="[id]"} 1
rtsps_conns_bytes_received{id="[id]"} 1234
rtsps_conns_bytes_sent{id="[id]"} 187

# metrics of every RTSPS session
rtsps_sessions{id="[id]",state="[state]"} 1
rtsps_sessions_bytes_received{id="[id]",state="[state]"} 1234
rtsps_sessions_bytes_sent{id="[id]",state="[state]"} 187

# metrics of every RTMP connection
rtmp_conns{id="[id]",state="[state]"} 1
rtmp_conns_bytes_received{id="[id]",state="[state]"} 1234
rtmp_conns_bytes_sent{id="[id]",state="[state]"} 187

# metrics of every WebRTC connection
webrtc_conns{id="[id]"} 1
webrtc_conns_bytes_received{id="[id]",state="[state]"} 1234
webrtc_conns_bytes_sent{id="[id]",state="[state]"} 187

pprof

A performance monitor, compatible with pprof, can be enabled with the parameter pprof: yes; then the server can be queried for metrics with pprof-compatible tools, like:

go tool pprof -text http://localhost:9999/debug/pprof/goroutine
go tool pprof -text http://localhost:9999/debug/pprof/heap
go tool pprof -text http://localhost:9999/debug/pprof/profile?seconds=30

Compile from source

Standard

Install Go ≥ 1.18, download the repository, open a terminal in it and run:

go build .

The command will produce the rtsp-simple-server binary.

Raspberry Pi

In case of a Raspberry Pi, the server can be compiled with native support for the Raspberry Pi Camera. Install Go ≥ 1.18, download the repository, open a terminal in it and run:

cd internal/rpicamera/exe
make
cd ../../../
go build -tags rpicamera .

The command will produce the rtsp-simple-server binary.

Compile for all supported platforms

Compilation for all supported platform can be launched by using:

make binaries

The command will produce tarballs in folder binaries/.

Publish to the server

From a webcam

To publish the video stream of a generic webcam to the server, edit rtsp-simple-server.yml and replace everything inside section paths with the following content:

paths:
  cam:
    runOnInit: ffmpeg -f v4l2 -i /dev/video0 -pix_fmt yuv420p -preset ultrafast -b:v 600k -f rtsp rtsp://localhost:$RTSP_PORT/$RTSP_PATH
    runOnInitRestart: yes

If the platform is Windows:

paths:
  cam:
    runOnInit: ffmpeg -f dshow -i video="USB2.0 HD UVC WebCam" -pix_fmt yuv420p -c:v libx264 -preset ultrafast -b:v 600k -f rtsp rtsp://localhost:$RTSP_PORT/$RTSP_PATH
    runOnInitRestart: yes

Where USB2.0 HD UVC WebCam is the name of your webcam, that can be obtained with:

ffmpeg -list_devices true -f dshow -i dummy

After starting the server, the webcam can be reached on rtsp://localhost:8554/cam.

From a Raspberry Pi Camera

rtsp-simple-server natively support the Raspberry Pi Camera, enabling high-quality and low-latency video streaming from the camera to any user. There are a couple of requisites:

The server must run on a Raspberry Pi, with Raspberry Pi OS bullseye or newer as operative system. Both 32 bit and 64 bit operative systems are supported.
Make sure that the legacy camera stack is disabled. Type sudo raspi-config, then go to Interfacing options, enable/disable legacy camera support, choose no. Reboot the system.

If you want to run the standard (non-containerized) version of the server:

Make sure that the libcamera0 package version is at least 0.0.2, otherwise upgrade it with sudo apt update && sudo apt install libcamera0.
download the server executable. If you're using 64-bit version of the operative system, make sure to pick the arm64 variant.
edit rtsp-simple-server.yml and replace everything inside section paths with the following content:
```
paths:
  cam:
    source: rpiCamera
```

If you want to run the server with Docker, you need to use the latest-rpi image (that already contains libcamera) and set some additional flags:

docker run --rm -it \
--network=host \
--privileged \
--tmpfs /dev/shm:exec \
-v /run/udev:/run/udev:ro \
-e RTSP_PATHS_CAM_SOURCE=rpiCamera \
aler9/rtsp-simple-server:latest-rpi

After starting the server, the camera can be reached on rtsp://raspberry-pi:8554/cam or http://raspberry-pi:8888/cam.

Camera settings can be changed by using the rpiCamera* parameters:

paths:
  cam:
    source: rpiCamera
    rpiCameraWidth: 1920
    rpiCameraHeight: 1080

All available parameters are listed in the sample configuration file.

From OBS Studio

OBS Studio can publish to the server by using the RTMP protocol. In Settings -> Stream (or in the Auto-configuration Wizard), use the following parameters:

Service: Custom...
Server: rtmp://localhost
Stream key: mystream

If credentials are in use, use the following parameters:

Service: Custom...
Server: rtmp://localhost
Stream key: mystream?user=myuser&pass=mypass

If you want to generate a stream that can be read with WebRTC, open Settings -> Output -> Recording and use the following parameters:

FFmpeg output type: Output to URL
File path or URL: rtsp://localhost:8554/mystream
Container format: rtsp
Check show all codecs (even if potentically incompatible
Video encoder: h264_nvenc (libx264)
Video encoder settings (if any): bf=0
Audio track: 1
Audio encoder: libopus

The use the button Start Recording (instead of Start Streaming) to start streaming.

From OpenCV

To publish a video stream from OpenCV to the server, OpenCV must be compiled with GStreamer support, by following this procedure:

sudo apt install -y libgstreamer1.0-dev libgstreamer-plugins-base1.0-dev gstreamer1.0-plugins-ugly gstreamer1.0-rtsp python3-dev python3-numpy
git clone --depth=1 -b 4.5.4 https://github.com/opencv/opencv
cd opencv
mkdir build && cd build
cmake -D CMAKE_INSTALL_PREFIX=/usr -D WITH_GSTREAMER=ON ..
make -j$(nproc)
sudo make install

You can check that OpenCV has been installed correctly by running:

python3 -c 'import cv2; print(cv2.getBuildInformation())'

And verifying that the output contains GStreamer: YES.

Videos can be published with VideoWriter:

import cv2
import numpy as np
from time import sleep

fps = 20
width = 800
height = 600

out = cv2.VideoWriter('appsrc ! videoconvert' + \
    ' ! x264enc speed-preset=ultrafast bitrate=600 key-int-max=40' + \
    ' ! rtspclientsink location=rtsp://localhost:8554/mystream',
    cv2.CAP_GSTREAMER, 0, fps, (width, height), True)
if not out.isOpened():
    raise Exception("can't open video writer")

while True:
    frame = np.zeros((height, width, 3), np.uint8)

    # create a red rectangle
    for y in range(0, int(frame.shape[0] / 2)):
        for x in range(0, int(frame.shape[1] / 2)):
            frame[y][x] = (0, 0, 255)

    out.write(frame)
    print("frame written to the server")

    sleep(1 / fps)

Read from the server

From VLC and Ubuntu

The VLC shipped with Ubuntu 21.10 doesn't support playing RTSP due to a license issue (see here and here).

To overcome the issue, remove the default VLC instance and install the snap version:

sudo apt purge -y vlc
snap install vlc

Then use it to read the stream:

vlc rtsp://localhost:8554/mystream

RTSP protocol

General usage

RTSP is a standardized protocol that allows to publish and read streams; in particular, it supports different underlying transport protocols, that are chosen by clients during the handshake with the server:

UDP: the most performant, but doesn't work when there's a NAT/firewall between server and clients. It doesn't support encryption.
UDP-multicast: allows to save bandwidth when clients are all in the same LAN, by sending packets once to a fixed multicast IP. It doesn't support encryption.
TCP: the most versatile, does support encryption.

The default transport protocol is UDP. To change the transport protocol, you have to tune the configuration of your client of choice.

TCP transport

The RTSP protocol supports the TCP transport protocol, that allows to receive packets even when there's a NAT/firewall between server and clients, and supports encryption (see Encryption).

You can use FFmpeg to publish a stream with the TCP transport protocol:

ffmpeg -re -stream_loop -1 -i file.ts -c copy -f rtsp -rtsp_transport tcp rtsp://localhost:8554/mystream

You can use FFmpeg to read that stream with the TCP transport protocol:

ffmpeg -rtsp_transport tcp -i rtsp://localhost:8554/mystream -c copy output.mp4

You can use GStreamer to read that stream with the TCP transport protocol:

gst-launch-1.0 rtspsrc protocols=tcp location=rtsp://localhost:8554/mystream ! fakesink

You can use VLC to read that stream with the TCP transport protocol:

vlc --rtsp-tcp rtsp://localhost:8554/mystream

UDP-multicast transport

The RTSP protocol supports the UDP-multicast transport protocol, that allows a server to send packets once, regardless of the number of connected readers, saving bandwidth.

This mode must be requested by readers when handshaking with the server; once a reader has completed a handshake, the server will start sending multicast packets. Other readers will be instructed to read existing multicast packets. When all multicast readers have disconnected from the server, the latter will stop sending multicast packets.

If you want to use the UDP-multicast protocol in a Wireless LAN, please be aware that the maximum bitrate supported by multicast is the one that corresponds to the lowest enabled WiFi data rate. For instance, if the 1 Mbps data rate is enabled on your router (and it is on most routers), the maximum bitrate will be 1 Mbps. To increase the maximum bitrate, use a cabled LAN or change your router settings.

To request and read a stream with UDP-multicast, you can use FFmpeg:

ffmpeg -rtsp_transport udp_multicast -i rtsp://localhost:8554/mystream -c copy output.mp4

or GStreamer:

gst-launch-1.0 rtspsrc protocols=udp-mcast location=rtsps://ip:8554/...

or VLC (append ?vlcmulticast to the URL):

vlc rtsp://localhost:8554/mystream?vlcmulticast

Encryption

Incoming and outgoing RTSP streams can be encrypted with TLS (obtaining the RTSPS protocol). A TLS certificate is needed and can be generated with OpenSSL:

openssl genrsa -out server.key 2048
openssl req -new -x509 -sha256 -key server.key -out server.crt -days 3650

Edit rtsp-simple-server.yml, and set the protocols, encryption, serverKey and serverCert parameters:

protocols: [tcp]
encryption: optional
serverKey: server.key
serverCert: server.crt

Streams can be published and read with the rtsps scheme and the 8322 port:

ffmpeg -i rtsps://ip:8322/...

If the client is GStreamer, disable the certificate validation:

gst-launch-1.0 rtspsrc tls-validation-flags=0 location=rtsps://ip:8322/...

At the moment VLC doesn't support reading encrypted RTSP streams. A workaround consists in launching an instance of rtsp-simple-server on the same machine in which VLC is running, using it for reading the encrypted stream with the proxy mode, and reading the proxied stream with VLC.

Redirect to another server

To redirect to another server, use the redirect source:

paths:
  redirected:
    source: redirect
    sourceRedirect: rtsp://otherurl/otherpath

Fallback stream

If no one is publishing to the server, readers can be redirected to a fallback path or URL that is serving a fallback stream:

paths:
  withfallback:
    fallback: /otherpath

Corrupted frames

In some scenarios, when reading RTSP from the server, decoded frames can be corrupted or incomplete. This can be caused by multiple reasons:

the packet buffer of the server is too small and can't keep up with the stream throughput. A solution consists in increasing its size:
```
readBufferCount: 1024
```
The stream throughput is too big and the stream can't be sent correctly with the UDP transport. UDP is more performant, faster and more efficient than TCP, but doesn't have a retransmission mechanism, that is needed in case of streams that need a large bandwidth. A solution consists in switching to TCP:
```
protocols: [tcp]
```
In case the source is a camera:
```
paths:
  test:
    source: rtsp://..
    sourceProtocol: tcp
```
The stream throughput is too big to be handled by the network between server and readers. Upgrade the network or decrease the stream bitrate by re-encoding it.

Decrease latency

The RTSP protocol doesn't introduce any latency by itself. Latency is usually introduced by clients, that put frames in a buffer to compensate network fluctuations. In order to decrease latency, the best way consists in tuning the client. For instance, latency can be decreased with VLC by decreasing the Network caching parameter, that is available in the Open network stream dialog or alternatively ca be set with the command line:

vlc --network-caching=50 rtsp://...

RTMP protocol

General usage

RTMP is a protocol that allows to read and publish streams, but is less versatile and less efficient than RTSP (doesn't support UDP, encryption, doesn't support most RTSP codecs, doesn't support feedback mechanism). It is used when there's need of publishing or reading streams from a software that supports only RTMP (for instance, OBS Studio and DJI drones).

At the moment, only the H264 and AAC codecs can be used with the RTMP protocol.

Streams can be published or read with the RTMP protocol, for instance with FFmpeg:

ffmpeg -re -stream_loop -1 -i file.ts -c copy -f flv rtmp://localhost/mystream

or GStreamer:

gst-launch-1.0 -v flvmux name=s ! rtmpsink location=rtmp://localhost/mystream filesrc location=file.mp4 ! qtdemux name=d d.video_0 ! queue ! s.video d.audio_0 ! queue ! s.audio

Credentials can be provided by appending to the URL the user and pass parameters:

ffmpeg -re -stream_loop -1 -i file.ts -c copy -f flv rtmp://localhost:8554/mystream?user=myuser&pass=mypass

Encryption

RTMP connections can be encrypted with TLS, obtaining the RTMPS protocol. A TLS certificate is needed and can be generated with OpenSSL:

openssl genrsa -out server.key 2048
openssl req -new -x509 -sha256 -key server.key -out server.crt -days 3650

Edit rtsp-simple-server.yml, and set the rtmpEncryption, rtmpServerKey and rtmpServerCert parameters:

rtmpEncryption: optional
rtmpServerKey: server.key
rtmpServerCert: server.crt

Streams can be published and read with the rtmps scheme and the 1937 port:

rtmps://localhost:1937/...

Please be aware that RTMPS is currently unsupported by VLC, FFmpeg and GStreamer. However, you can use a proxy like stunnel or nginx to allow RTMP clients to access RTMPS resources.

HLS protocol

General usage

HLS is a protocol that allows to embed live streams into web pages. It works by splitting streams into segments, and by serving these segments with the HTTP protocol. Every stream published to the server can be accessed by visiting:

http://localhost:8888/mystream

where mystream is the name of a stream that is being published.

Browser support

Although the server can produce HLS with a variety of video and audio codecs (that are listed at the beginning of the README), not all browsers can read all codecs. You can check what codecs your browser can read by visiting this page:

https://jsfiddle.net/4msrhudv

If you want to increase the compatibility of the stream in order to support most browsers, you have to re-encode it by using the H264 and AAC codecs, for instance by using FFmpeg:

ffmpeg -i rtsp://original-source -pix_fmt yuv420p -c:v libx264 -preset ultrafast -b:v 600k -c:a aac -b:a 160k -f rtsp rtsp://localhost:8554/mystream

Embedding

The simples way to embed a HLS stream into a web page consists in using an iframe tag:

<iframe src="http://rtsp-simple-server-ip:8888/mystream" scrolling="no"></iframe>

For more advanced options, you can create and serve a custom web page by starting from the source code of the default page.

Low-Latency variant

Low-Latency HLS is a recently standardized variant of the protocol that allows to greatly reduce playback latency. It works by splitting segments into parts, that are served before the segment is complete.

LL-HLS is disabled by default. To enable it, a TLS certificate is needed and can be generated with OpenSSL:

openssl genrsa -out server.key 2048
openssl req -new -x509 -sha256 -key server.key -out server.crt -days 3650

Set the hlsVariant, hlsEncryption, hlsServerKey and hlsServerCert parameters in the configuration file:

hlsVariant: lowLatency
hlsEncryption: yes
hlsServerKey: server.key
hlsServerCert: server.crt

Every stream published to the server can be read with LL-HLS by visiting:

https://localhost:8888/mystream

If the stream is not shown correctly, try tuning the hlsPartDuration parameter, for instance:

hlsPartDuration: 500ms

Decrease latency

in HLS, latency is introduced since a client must wait for the server to generate segments before downloading them. This latency amounts to 1-15secs depending on the duration of each segment, and to 500ms-3s if the Low-Latency variant is enabled.

To decrease the latency, you can:

enable the Low-Latency variant of the HLS protocol, as explained in the previous section;
if Low-latency is enabled, try decreasing the hlsPartDuration parameter;
try decreasing the hlsSegmentDuration parameter;
The segment duration is influenced by the interval between the IDR frames of the video track. An IDR frame is a frame that can be decoded independently from the others. The server changes the segment duration in order to include at least one IDR frame into each segment. Therefore, you need to decrease the interval between the IDR frames. This can be done in two ways:
- if the stream is being hardware-generated (i.e. by a camera), there's usually a setting called Key-Frame Interval in the camera configuration page
- otherwise, the stream must be re-encoded. It's possible to tune the IDR frame interval by using ffmpeg's -g option:
```
ffmpeg -i rtsp://original-stream -pix_fmt yuv420p -c:v libx264 -preset ultrafast -b:v 600k -max_muxing_queue_size 1024 -g 30 -f rtsp rtsp://localhost:$RTSP_PORT/compressed
```

WebRTC protocol

General usage

Every stream published to the server can be read with WebRTC by visiting:

http://localhost:8889/mystream

Usage inside a container or behind a NAT

If the server is hosted inside a container or is behind a NAT, additional configuration is required in order to allow the two WebRTC parts (the browser and the server) to establish a connection (WebRTC/ICE connection).

A first method consists into forcing all WebRTC/ICE connections to pass through a single UDP server port, by using the parameters:

# public IP of the server
webrtcICEHostNAT1To1IPs: [192.168.x.x]
# any port of choice
webrtcICEUDPMuxAddress: :8189

The NAT / container must then be configured in order to route all incoming UDP packets on port 8189 to the server. If you're using Docker, this can be achieved with the flag:

docker run --rm -it \
-p 8189:8189/udp
....
rtsp-simple-server

If the UDP protocol is blocked by a firewall, all WebRTC/ICE connections can be forced to pass through a single TCP server port:

# public IP of the server
webrtcICEHostNAT1To1IPs: [192.168.x.x]
# any port of choice
webrtcICETCPPMuxAddress: :8189

The NAT / container must then be configured in order to redirect all incoming TCP packets on port 8189 to the server. If you're using Docker, this can be achieved with the flag:

docker run --rm -it \
-p 8189:8189
....
rtsp-simple-server

Finally, if none of these methods work, you can force all WebRTC/ICE connections to pass through a TURN server, like coturn, that must be configured externally. The server address and credentials must be set in the configuration file:

webrtcICEServers: [turn:user:pass:host:ip]

Where user and pass are the username and password of the server.

If the server uses a secret-based authentication (for instance, coturn with the use-auth-secret option), it must be configured in this way:

webrtcICEServers: [turn:AUTH_SECRET:secret:host:ip]

where secret is the secret of the TURN server. rtsp-simple-server will generate a set of credentials by using the secret, and credentials will be sent to clients before the WebRTC/ICE connection is established.

Embedding

The simples way to embed a WebRTC stream into a web page consists in using an iframe tag:

<iframe src="http://rtsp-simple-server-ip:8889/mystream" scrolling="no"></iframe>

For more advanced options, you can create and serve a custom web page by starting from the source code of the default page.

Standards

RTSP/RTP/RTCP standards https://github.com/aler9/gortsplib#standards
HTTP 1.1 https://datatracker.ietf.org/doc/html/rfc2616
HLS https://datatracker.ietf.org/doc/html/rfc8216
HLS v2 https://datatracker.ietf.org/doc/html/draft-pantos-hls-rfc8216bis
Opus in MP4/ISOBMFF https://opus-codec.org/docs/opus_in_isobmff.html
Golang project layout https://github.com/golang-standards/project-layout

Links

Related projects

gortsplib (RTSP library used internally) https://github.com/aler9/gortsplib
pion/sdp (SDP library used internally) https://github.com/pion/sdp
pion/rtp (RTP library used internally) https://github.com/pion/rtp
pion/rtcp (RTCP library used internally) https://github.com/pion/rtcp
notedit/rtmp (RTMP library used internally) https://github.com/notedit/rtmp
go-astits (MPEG-TS library used internally) https://github.com/asticode/go-astits
go-mp4 (MP4 library used internally) https://github.com/abema/go-mp4
https://github.com/flaviostutz/rtsp-relay

Name		Name	Last commit message	Last commit date
Latest commit History 1,454 Commits
.github		.github
apidocs		apidocs
bench		bench
internal		internal
scripts		scripts
.dockerignore		.dockerignore
.gitignore		.gitignore
.golangci.yml		.golangci.yml
LICENSE		LICENSE
Makefile		Makefile
README.md		README.md
go.mod		go.mod
go.sum		go.sum
logo.png		logo.png
main.go		main.go
openwrt.mk		openwrt.mk
rtsp-simple-server.yml		rtsp-simple-server.yml

License

VitalyVaryvdin/rtsp-simple-server

Folders and files

Latest commit

History

Repository files navigation

Important announcement

Table of contents

Installation

Standard

Docker

OpenWRT

Basic usage

General

Configuration

Authentication

Encrypt the configuration

Proxy mode

Remuxing, re-encoding, compression

Save streams to disk

On-demand publishing

Start on boot

Linux

Windows

HTTP API

Metrics

pprof

Compile from source

Standard

Raspberry Pi

Compile for all supported platforms

Publish to the server

From a webcam

From a Raspberry Pi Camera

From OBS Studio

From OpenCV

Read from the server

From VLC and Ubuntu

RTSP protocol

General usage

TCP transport

UDP-multicast transport

Encryption

Redirect to another server

Fallback stream

Corrupted frames

Decrease latency

RTMP protocol

General usage

Encryption

HLS protocol

General usage

Browser support

Embedding

Low-Latency variant

Decrease latency

WebRTC protocol

General usage

Usage inside a container or behind a NAT

Embedding

Standards

Links

About

Resources

License

Stars

Watchers

Forks

Releases

Packages 0

Languages

Packages